Anagram & Information om | Engelska ordet CAMS

Exempel på hur man kan använda CAMS i en mening

• A camshaft is a shaft that contains a row of pointed cams in order to convert rotational motion to reciprocating motion.
• It consists of two, three, or four cams mounted on a common axle or two adjacent axles, so that pulling on the axle forces the cams to spread further apart.
• Devices that cause speed changes or changes to or from reciprocating to rotary motion, using means such as gears, pulleys or sheaves and belts, shafts, cams and cranks, usually are considered machines.
• As a racing-car engine it was hampered by a high center of gravity, and it was heavy and complex, with gear-driven twin overhead cams for each of four cylinder heads, two gear-coupled crankshafts, and mechanical fuel injection.
• A camshaft, a shaft to which cams are attached, was described in 1206 by al-Jazari, who employed them in his automata, water clocks (such as the candle clock) and water-raising machines.
• The rotary combination locks found on padlocks, lockers, or safes may use a single dial which interacts with several parallel discs or cams.
• However, some of the early VF models suffered mechanical problems, mainly as a result of poor quality camshafts (the "chocolate cams").
• It is typically powered by a wound spring made of whalebone, and the actions are controlled by a set of cams and levers.
• Despite this, the range dials on the gunsights at the time of construction were graduated to 15 degrees; super-elevating cams and prisms to allow the full elevation of the guns to be used were issued some time after the Battle of Jutland.
• An electric motor drives a shaft on which is arranged a series of cams or a drum studded with pegs along its surface.
• A desmodromic valve has two cams and two actuators, for positive opening and closing without a return spring.
• Like the original Gatling gun, the entire firing cycle is actuated by cams and powered by the rotation of the barrels.
• In the internal combustion engine, this task is performed by cams on a camshaft driving poppet valves, but this arrangement is not commonly used with steam engines, partly because achieving variable engine timing using cams is complicated.
• From a maintenance point of view, the most important part of the mechanical clocks was to ensure that they were well oiled to minimise wear on the cams and to replace blown bulbs in the optical pickups from the glass disk recordings.
• The ZF "sliding pins and cams" became available, and one example was the Type B-70 used during the Second World War in the military VWs (Kübelwagen and Schwimmwagen), although technically this was not a limited-slip differential, but a system composed of two freewheels, which sent the whole of the engine power to the slower-turning of the two wheels.
• In very soft rock, nuts and cams both can blow right through the rock and out of their placements, even with forces as small as those generated by tugging to "set" the piece.
• Pitons are still found in place (as "fixed" pitons) on some established free climbing routes, as fixed belay station anchors, in places where nuts or cams do not work; and are used on some hard aid climbs.
• The Electromatic typewriter patents document the use of pivoted spiral cams operating against a hard rubber drive roller to drive the print mechanism.
• The camshafts were designed by Florida-based Crane Cams and were manufactured by Maserati in Modena.
• Some of the pertinent features of the VH45DE are forged steel crankshaft, forged steel connecting rods, 6 Bolt main bearing caps with studs, full-length main bearing girdle, lightweight, floating pistons with molybdenum coating, sodium-filled exhaust valves, cross-flow cooling system, hydraulic lash adjusters, single-row silent timing chain, coil-on-plug ignition system, lifter buckets ride directly on cams to reduce friction, redline of 6900 rpm, compression ratio of 10.

Förberedelsen av sidan tog: 149,72 ms.